Hi,
First excuse my english (I'm french) so don't laught on me :grinthumb

I resently installed a QBic EQ3401 from Soltek with Windows XP SP2, 512 RAM (2x256) (DDR 2700) Intel Pentium 2Ghz, a Pinnacle PCTV, a ubc to lp1 printer cable, a HP 4L, a Hunday LCD 17' Screen.

here is my message in french

Le système d'événements de COM+ a détecté
un code de renvoi erroné lors de son traitement interne.
Le HRESULT est C0000005 à partir de la ligne 44
de d:\qxp_slp\com\com1x\src\events\tier1\eventsystemobj.cpp...

in english seems to be :

The COM+ Event System detected a bad return code during its internal processing. HRESULT was C0000005 from line 44 of d:\qxp_slp\com\com1x\src\events\tier1\eventsystemobj.cpp. Please contact Microsoft Product Support Services to report this error
It append sometimes in Word or when I play a divx movie...

I put my minidump atach to the message, I wish I could understand them but I think I'll read chineese before that ;-)

tomorrow I will do some tests :
- try to flash the bios, and try to change memory slots...
If you can give me a clue, or where I should begin...

Thanx you in advance

Skalpa

Hello and welcome to Techspot.

I believe you have a ram problem.

3 minidumps crash with memory corruption, and a bugcheck of 7F.

1 minidump crashes at win32k.sys. It has a bugcheck of 7F.

1 minidump crashes at ati3d1ag.dll. It has a bugcheck of 50.

1 minidump crashes at win32k.sys. It has a bugcheck of 50.

Go HERE and follow the instructions for testing your ram/hdd/page file.

0x0000007F: UNEXPECTED_KERNEL_MODE_TRAP

One of three types of problems occurred in kernel-mode: (1) Hardware failures. (2) Software problems. (3) A bound trap (i.e., a condition that the kernel is not allowed to have or intercept). Hardware failures are the most common cause (many dozen KB articles exist for this error referencing specific hardware failures) and, of these, memory hardware failures are the most common.

0x00000050: PAGE_FAULT_IN_NONPAGED_AREA

Requested data was not in memory. An invalid system memory address was referenced. Defective memory (including main memory, L2 RAM cache, video RAM) or incompatible software (including remote control and antivirus software) might cause this Stop message, as may other hardware problems (e.g., incorrect SCSI termination or a flawed PCI card).

Regards Howard :wave: :wave:

Thank you, that was fast :bounce:
Ok I will check the memory.
Is it possible that a hard drive failure could make these problems ?

Yes it is possible.

Follow the instructions for testing the ram/hard drive/page file.

Regards Howard

Hi,
That's what I've done so far :
-I flash the soltek motherboard with the last bios update.
-I test the memory (7 pass) with the last version of memtest -> No errors
-I change the virtual memory (delete/rebot/recreate)

Sometime when reading a DVD, I have a message like
The device, \Device\CdRom0, has a bad block when Fast Forwarding
before the PC reboots.
Is it because the DVD is damaged or the DVD-Player/Burner (new one)

I put the last Driver for my ATI Graphic card.

Test is now in progress...

Some faulty ram can pass memtest.

Try running with just one stick of ram. Also, try moving the ram to a different dim slot.

Check that your psu is powerful enough for your system.

Check your mobo for bulging, or leaking capacitors. See HERE for further info.

Although the ram/psu/mobo are the most likely culprits, it could be just about any hardware that`s causing the problem.

Unfortunately your minidumps don`t say exactly which hardware is faulty.

Regards Howard

Driver_not_less_or_equal

So,
I change the hardrive and reinstall the whole thing.
It was fine untill I reinstalled the usb to lpt1 cable, and canon lide 30 driver and HP printer driver.

The same pb with another hard drive

I will try to reinstall without them...

crash again !
DRIVER_NOT_LESS_OR_EQUAL
here is my minidump

Thanx All !
I change a setting in the bios.
I think it's Hard disk Write Protect to Disabled and now it works fine.

http://www.2cpu.com/gallery/soltek_eq3401a/BIOS_IDE

By