TechSpot

Bsod

By copoiu
Dec 4, 2006
  1. after BSOD in my event viewer I have this error codes. I have attached "dump" files. please look at them and give your oppinion. Thanks in advance!

    Error code 100000c5, parameter1 0110070e, parameter2 00000002, parameter3 00000001, parameter4 805446f3.
    Error code 100000d1, parameter1 70034353, parameter2 00000002, parameter3 00000008, parameter4 70034353.
    Error code 1000000a, parameter1 80580148, parameter2 00000002, parameter3 00000008, parameter4 80580148.

    the BSOD apears when computer is idle, after welcome screen or crash in apps.
     
  2. Tmagic650

    Tmagic650 TS Ambassador Posts: 20,934   +167

    BSOD's are commonly caused by dieing power supplies, bad memory and failing hardware. If you haven't messed with the bios, or added or deleted and files or programs, you can start troubleshooting your memory and your hard drive
     
  3. copoiu

    copoiu TS Rookie Topic Starter

    the power supplies in Enlight 400W, a very god one.
    with BIOS I don't mess up
    memory is Geil 2,5-4-4-8 dual channel kit with 97 months guaranty left and was tested in DOS mode with memtest for over 7 hours with no error

    I analyze the dump with WinDbg:

    DRIVER_CORRUPTED_EXPOOL (c5)
    An attempt was made to access a pageable (or completely invalid) address at an
    interrupt request level (IRQL) that is too high. This is
    caused by drivers that have corrupted the system pool. Run the driver
    verifier against any new (or suspect) drivers, and if that doesn't turn up
    the culprit, then use gflags to enable special pool.
    Arguments:
    Arg1: 0110070e, memory referenced
    Arg2: 00000002, IRQL
    Arg3: 00000001, value 0 = read operation, 1 = write operation
    Arg4: 805446f3, address which referenced memory
    MODULE_NAME: snpstd3

    FAULTING_MODULE: 804d7000 nt

    DEBUG_FLR_IMAGE_TIMESTAMP: 435f4813

    BUGCHECK_STR: 0xC5_2

    CURRENT_IRQL: 2

    FAULTING_IP:
    nt+6d6f3
    805446f3 897104 mov dword ptr [ecx+4],esi

    CUSTOMER_CRASH_COUNT: 1

    DEFAULT_BUCKET_ID: WRONG_SYMBOLS

    LAST_CONTROL_TRANSFER: from f5be4b6a to 805446f3

    STACK_TEXT:
    WARNING: Stack unwind information not available. Following frames may be wrong.
    f3767b9c f5be4b6a 00000000 00000001 70627375 nt+0x6d6f3
    f3767bd4 f5bf0cc9 86277028 73635254 862adb68 USBPORT+0x7b6a
    f3767c0c f5bf5dfe 862c9198 86277028 00000180 USBPORT+0x13cc9
    f3767c2c f5bdf1e2 862c9198 8502a590 8502a590 USBPORT+0x18dfe
    f3767c50 804ede0d 8502a648 862c92f0 850504e8 USBPORT+0x21e2
    f3767c68 f51b12d9 8502a590 862c9198 8502a590 nt+0x16e0d
    f3767c88 f51b1afa 862a3698 8502a590 00000000 usbhub+0x42d9
    f3767ca4 f51af1d8 850504e8 8502a590 f3767cfc usbhub+0x4afa
    f3767cb4 804ede0d 862fe2b8 8502a590 861a7258 usbhub+0x21d8
    f3767cfc ed371273 850504e8 000000f1 00000000 nt+0x16e0d
    f3767d18 ed36c768 00000018 00000000 00000008 snpstd3+0x39273
    f3767d40 ed37021c 00000008 00000002 000000f1 snpstd3+0x34768
    f3767da8 ed370981 805c4a24 861a7258 00000000 snpstd3+0x3821c
    f3767ddc 80540fb2 ed370974 861a7258 00000000 snpstd3+0x38981
    00000000 00000000 00000000 00000000 00000000 nt+0x69fb2


    STACK_COMMAND: kb

    FOLLOWUP_IP:
    snpstd3+39273
    ed371273 ?? ???

    SYMBOL_STACK_INDEX: a

    FOLLOWUP_NAME: MachineOwner

    IMAGE_NAME: snpstd3.sys

    SYMBOL_NAME: snpstd3+39273

    BUCKET_ID: WRONG_SYMBOLS

    Followup: MachineOwner

    I think it was from USB no name camera, it is now uninstalled, I have to test and see if BSOD reapears.

    p.s. sorry for bad english, I'm romanian :)
     
  4. cpc2004

    cpc2004 TS Rookie Posts: 2,044

    One miniudmp is insufficient to determine the culprit. Zip more minidumps and attach the zip file here. Bugcheck C5 is usually related to fautly ram. However I cannot confirm unless you provide more minidumps.
     
  5. copoiu

    copoiu TS Rookie Topic Starter

    the problem is not from USB camera, i've uninstalled the drivers but now I have another error: Probably caused by : ntoskrnl.exe ( nt+59e01 )
     
  6. cpc2004

    cpc2004 TS Rookie Posts: 2,044

    Yours windows is crashed random and this is the symptom of hardware error. Probably the culprit is faulty ram. Reseat the memory to another memory slot and clean the dust inside the memory slot. If it still crashes, run memtest to stress test the ram.
     
  7. copoiu

    copoiu TS Rookie Topic Starter

    I first begin with a thanck you for help.
    I attach a image with a test ram from ms-dos (Hiren's CD boot) with memtest v.1.65
    as you can see this test is standard with 11 pass and over 5h continuos test with NO errors.
    before this test I have reseat the memory and another BSOD apears.
    what next?
     

    Attached Files:

  8. cpc2004

    cpc2004 TS Rookie Posts: 2,044

    Some faulty ram can pass memtest. If you have ram at another PC, swap the ram and see what happen.
     
  9. copoiu

    copoiu TS Rookie Topic Starter

    I have some Kingstone's at my brother computer, one 512 an another of 256Mb. let's swap and test ... get back with results in 2-3 days. 10x!

    p.s. with original memory (Geil) my computer was tested another 5 h with burning test Everest and no errors, the BSOD apears when computer is idle, after welcome screen about 1h. after computer warms the BSOD don't apears ... :mad:
     
  10. copoiu

    copoiu TS Rookie Topic Starter

    WiTH your Help, I have found THe problem. IT waS THe VolTage for ram. I HaVe manualy SeT and now iT iS ok.
    ... STupid keyboard... :)
     
  11. cpc2004

    cpc2004 TS Rookie Posts: 2,044

    Do you mean you overclock the RAM?
     
     
  12. copoiu

    copoiu TS Rookie Topic Starter

    this is the ram: http://www.geilusa.com/proddetail.asp?linenumber=36 - CAS 2.5-8-4-4 (GE5123200BDC & GE1G3200BDC), in BIOS now it's set to 2,60V and no more BSOD for 3 days now. with default and above 2,70V i have BSOD very often. this error I have only with my new ASUS A7N5X mobo, with the old one Gigabite K8NSC I have overclock the AMD 3000+ venice & memory with no errors like this:
    Multiplicator HTT: 3X
    Multiplicator CPU: 9X (default)
    FSB: 267MHZ
    Memory timings: 2-3-3-7 (CL-RCD-RP-RAS) (default)
    Command rate(CR): 1T
    CPU Voltage: 1.400 V (default)
    Memory Voltage: 2.500 V (default)
    CPU/DDR Ratio: 2/1.5
    Temperatura max:
    - Idle: 29-31
    - Full: 38-39
    I think this new mobo is worst then old one, I do this "upgrade" for PCI-E, now I am very sorry beacause with this one I can't do any overclock.
    Now the sistem it's perfect stable but I don't have de performance like I want...
     
Topic Status:
Not open for further replies.


Add New Comment

TechSpot Members
Login or sign up for free,
it takes about 30 seconds.
You may also...


Get complete access to the TechSpot community. Join thousands of technology enthusiasts that contribute and share knowledge in our forum. Get a private inbox, upload your own photo gallery and more.