Hi all,
After I knocked my Zalman CNPS-9500AM2 while rewiring all the power cables in my new pc, the temps while idling went up by about 5 Celcius (Not really a problem as still idles at 33), So I took of the heatsink and wiped off the old thermal paste, Put some more on etc
The problem is I accidentally wiped a tiny amount of the thermal paste onto the base of about 5 of the pins on the edge of the underside. I wiped all that I could off but it looks to me like theres enough there to short some of the pins (if the paste conducts).
Will this cause a problem?
Should I boot up and see what happens?
Any idea for somthing small enough to clean between the pins?
Thanks for any advice
ps. thanks for putting up with my endless questions about my new pc

Well, bit of a tough spot there. What kind of thermal paste did you use? As far as I know, they are all excellent conductors (especially arctic silver) and you do not want to try starting your system with that on your pins.

Never had it happen, so I can't say for sure how to clean it out, but if it were me I would carefully try and wash it off with some solvent. You're going to need to be very careful not to damage any pins.... Good luck!

Actually, I've heard that AS is the least conductive out of all of them:
Though, they still recommend to keep it out of stuff like pins....

It was the stuff that came with the heatsink...I got a resistance of 3500ohms across 1mm of it on a sheet of paper. It wasnt the most accurate experiment i've ever conducted though.
Do all alcohols dissolve it or just propyl alcohols?

btw any Antec P180 owners here, does it matter which way up you put the psu in?? (didnt think it was worth starting a new thread)

Easy......

You need an artic silver cleaning kit, and a paper towel.

Take a paper towel and fold it until it fits perfectly in between the cpu pins. While the paper towel is inserted between the pins (in the place you intend to clean) gently drop 2 tabs of artic silver thermal material remover near the pins and paper towel and let it soaks the towel, so the liquid contacts the pins or dirty areas. then gently move the wet towel slowly back and forth between the pins to clean the thermal paste off

Repeat the same way with artic silver surface purifier and it gets the job done. All liquids are safe for the cpu pins.

I find that the super absorbant paper towels work best.

I was in this situation myself.

Hope this helps

btw any Antec P180 owners here, does it matter which way up you put the psu in?? (didnt think it was worth starting a new thread)[/QUOTE]

If you want to use the silent padded drive cage:

1.If your PSU has normal 80mm fans, any way will work.

2.If your PSU has 120mm fans underneath the PSU, you are forced to install it upside down.



If you dont want to use the silent padded drive cage, you can install the PSU the regular way with screws and any way will work.

Heres mine!
http://img209.imageshack.us/my.php?image=img0008yu2.jpg

I cleaned a cpu a few months ago with just isoprople alchohol and a paper towel. Worked great.

doug

Denatured alcohol works best... It has much less water in it than Isopropyl alcohol

Distilled water, impurities are what conducts, dust etc.

Too much water can cause rusting and corrosion

Cleared it off this morning and its worked fine.
Thanks all, especially wallabing

I personally prefer Acetone. I think it does a much better job of takeing off thermal compound and evaporates much quicker than alcohol.

If you can find any...dimethylsulphoxide works brilliantly (what ive been using)

In the US most drugstores carry 99% Isopropyl, you don't have to worry about water at that percentage, just regular Isopropyl is like 70%. So pay attention to percentages.

Acetone will work fine too, but be careful with it. Isopropyl is much more tolerant of plastics than Acetone. For example you can clean cds with isopropyl, but acetone dissolves the plastic (at least on cdrs).

I used acetone alot in the 70's for cleaning electronic circuit boards. It was outlawed for its toxic carcenogenic fumes in the early 80's. Denatured alcohol evaproates quickly too and a pint bottle costs about $5.50 at any drug store here in the USA. I also use this to clean video heads, metal and rubber parts and belts

outlawed?? since when, here in PA I can buy it at any hardware store for about $4 a quart.

Outlawed for industrial use in California... Denatured alcohol has less smelly fumes than acetone, even though you might not put your nose too close to an open bottle of denatured either

First time poster here, but I just wanted to give thanks for this thread, as it helped me out greatly yesterday.

Never again will I use so much thermal paste.

You shouldn't ever use too much thermal paste anyway, it doesn't help dissipate heat, just helps transferring heat. Its not a great heat conductor to start with, just a heck lot better than air (and this goes for AS5 as well).

The less the better in this case.

As for the initial problem, as long as they're not shorting the pins, I wouldn't worry about it. If it is, do as wallabing mentioned: fold a paper towel or something, and use it to wipe the stuff off. I'd personally use isopropyl alcohol to clean it, mainly cos it dries up real fast.

i just clean my cpu pins with a old toothbrush and washing liquid. the pins are clean now and i let the cpu to get dry. i took the risk but i will wait to see what will happen next. at least the toothbrush did a very good job and cleaned all the cpu without damaging the pins. but of cource i will not use the same toothbrush to clean my teath! the old thermal paste was silver colour. i decided to clean the cpu pins because after i placed a new silicon thermal paste in the cpu the motherboard speaker was making continously a noise but the xp boot with no problem. i hope it was the old silver thermal paste between the cpu pins and not a motherboard problem.