Setup did not find any hard disk drives installed in your computer

S

smartboy

Heres my problem , so my computer dvd and cd drives failed i kept getting mssg select boot device and reboot. then i used a cd drive fromanother computer connected it with xp windows cd and now im getting error in setup"setup did not find any hard disk drives installed in your computer" please help this computer used to work fine before and was xp before..thankyou in advance!
 
Check you bios settings if it is detecting your HDD.

/edit/

Check also the jumper settings of the CD drive
 
what do u mean hdd ? settings where?

igetwhat ur saying press 'F2 and settings but what exactly and jumper settings?
 
Can you give a description of the CD drive? Is it using IDE? If it is make the jumper settings to Primary Master then on the HDD set it to slave.

42473_cd1.gif


/edit/

It would be helpful if you specify your specs, like what is your BIOS is it AMI or others, your HDD, SATA or IDE as well as size, and also for the CD.

Based on your first post you are reinstalling XP, thus you are getting that error message.

Have you tried this one, Removing the CD drive and setting the HDD as the first Boot device on your BIOS, then boot normally?
 
1, 2 and 4 are being used its a lg disc compact


It starts up with primary master hard disk error press f4 to resume

auto detecting usb mass storage devices 00 usb mass storage devies foundand confgired. atapi cdrom sm hl dl st GCE 8527b\

Intel corporation D845GVSR DESKTOP BOARD
SERIAL NUMBER AZSR42217140
VA84510A.86A.0030.P10.0402160229

INTEL (R) PENTIUM (R) 4 PRCESSOR, 2A GHZ

255MB SYSTEM RAM
 
THE FIRST PIORTITY BOOT SETTING

all my booting devices have failed.. im usingaboot device that i took out fromanother computer sothis is the first and only piorty boot setting.
 
whats hdd? hard diskdrive? where do i found infromation about itidont know.
 
Remove the CD drive.

Boot your PC. Go to BIOS setup. Set everything to Default (something like pressing F9, or selecting Load Optimal Settings)

Now is your HDD detected?
 
ok holdonthere is a optimal defualt thing ill try it one minute
 
It's not being detected.

Carefully remove the IDE and power cable of the HDD and put it again tightly. Same with the other end of the cable that connects to the board

IDE_Hard-drive_with_IDE_and_Power_cable_crop-600x485.jpg
 
idont know if this is related?

underadvanced > Ide Config.
IdeController : Both
PCI IDE BUS MASTER :Enabled
Hard Disk Predelay: Disabled
Primary Ide Master: Wdc ROM MODEL MAMMOTH
PRIMARY IDE SLAVE : NOT DETECTED
SEC ID MASTER AND ID SLAVE NOT DETECTED ASWELL
 
Where is this cablesir? Because i think this might be the problem i did mess with the cablesaccidently.
 
Don't connect the CD yet.

One at a time. HDD first. We'll deal with the CD later

refer to post #4

set the jumper to master
 
omgi seethe hddd there is no wire connected to it at all is it suppose to be?
 
ok i did but i still am getting nothing no detection ireconected themtoo one more question the ide cablehas 2 outputs leading from the mother board output i used the end one not the middleone.
 
You can use any. Now if there is still no detection, try the other one on the motherboard.

Also try the other molex

Molex-style-power-connector.jpg


Still have problems, Try a different power supply unit and IDE cable
 
You must log in or register to reply here.

Similar threads

G
Beware of WD Sandisk RMA Support
Replies
0
Views
162
grady115
G
A
Western Digital's plans for HAMR hard disk drives will materialize in 2027
Replies
0
Views
166
Alfonso Maruccia
A
Julio Franco
Used Seagate drives sold as new traced back to crypto mining farms
Replies
12
Views
542
Aaron Jones
Aaron Jones

Latest posts

Back