TechSpot

HDD Led, Power Sw etc. connectors

By P3ANUT
Aug 12, 2008
  1. Hi, Well today i cleaning my computer, & made a mistake by pulling these out, I need help on how to connect these
    connections ... I check other threads and sites but none of them give me the information needed.
    Connections :
    (Power Led = Green) (Power Sw = Yellow) (H.D.D Led = Red) (Reset Sw =Blue) ...

    I took side shots of my pc so it could give you more of a visual ....
    Code:
    http://i34.tinypic.com/23kx0ra.jpg
    http://i36.tinypic.com/25gxcly.jpg
    http://i33.tinypic.com/208wah2.jpg
    http://i37.tinypic.com/3308nbn.jpg
    http://i34.tinypic.com/1127h9d.jpg
    http://i33.tinypic.com/10qavrt.jpg
    
    
    -Thanks P3anut
     
  2. P3ANUT

    P3ANUT TS Rookie Topic Starter Posts: 30

    Any one can help me please ??
    -Thanks
     
  3. P3ANUT

    P3ANUT TS Rookie Topic Starter Posts: 30

    Hi can any body help please,, i need advice / help to connect these connectors
    -Thanks
     
  4. raybay

    raybay TS Evangelist Posts: 7,241   +9

    You need the schematics from the manual of the maker. We cannot guess for you online... And even the same models of comptuers have different wiring schemes depending on where they were on what day on the assembly line.
     
  5. Rick

    Rick TechSpot Staff Posts: 4,573   +65

    They are labeled on the board...

    They are labeled on the computer case...

    All you have to do is connect them as they are labeled - ignore the colors. According to what you've said, it should be as follows:

    Case -------> Board
    Yellow --> Red (Power switch)
    Red --> Orange (HDD light)
    Green --> Green (Power led)
    Blue --> Blue (Reset switch)


    There's no need for 'schematics'. You have labels for everything. And even if you connect the wrong headers, you won't damage anything. The only room for error now is having the headers plugged in upside down, and this doesn't matter for the reset switch and power switches. They will work regardless. If you're HDD and power lights don't work, flip the connector around and try it again.
     
  6. P3ANUT

    P3ANUT TS Rookie Topic Starter Posts: 30

    The green one has 3 holes ??? how do i connect it?
    do i just connect two- out of three holes??? Will it work ??
     
  7. P3ANUT

    P3ANUT TS Rookie Topic Starter Posts: 30

    Hi, Its been while since Ive toy around with this PC
    today i was reviewing this post, And i agree on giving this another shot,
    So far i follow the advice you give me ^^
    The Power LED, Is connected correctly, When i plug the cord into the CPU & (Switch on the power on the back of the CPU) , the Green Led Light Power's Up. The only problem am having is ACTUALLY POWERING UP THE CPU.
    I have every thing connected According to the post above^^.
    When i Switch the power on & off (Computer switch in the back), the sound card has a light and it flashes green, so am assuming the mother board works correct?

    Possibly Problem?
    The only thing Ive notice is that (The Power SW)(Yellow)
    Has Two Pins to plug into (and on the motherboard it only has one pin entry were it Says PWRSW,) Could that be the problem?
    (The Power Led (Green) has Three Pins to plug into,) So when i plug it in it takes up one RED Pin Entry,) Bare with me , am trying to be as specific as i can,
    -Thanks to for those who help =)
     
Topic Status:
Not open for further replies.

Similar Topics

Add New Comment

You need to be a member to leave a comment. Join thousands of tech enthusiasts and participate.
TechSpot Account You may also...