TechSpot

Nero reports "Burn Process Failed"

By satter21
Feb 23, 2007
Topic Status:
Not open for further replies.
  1. Hi, I was having a few problems burning to a DVD disk and thought wold share this to try and see if there is anything someone may think of that I already haven't...

    I'm trying to burn a DVD video disk, which i've burnt ok previously...
    I'm using a BTC 1008 DVD Writer, Ritek disks and tried Nero 6 and then now also tried with Nero 7 .... BUT.... I keep getting the error "burn process failed".

    I've tried about a dozen times now and just get the same thing, Nero gets to 2% (while its still in Lead-In) then just reports the "burn process failed" error.

    I've used the Ritek disks I'm using before without any problems and to rule out the disks being an issue I've even tried a Verbatim and a Datawrite.

    Below is the log file from Nero,

    NT-SPTI used
    Nero Version: 7.5.9.1
    Internal Version: 7, 5, 9, 1

    Recorder: <DVDRW IDE1008> Version: 0052 - HA 1 TA 0 - 7.5.9.1
    Adapter driver: <IDE> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ?
    CD-ROM: <DVDROM 1 0X >Version: 41 - HA 1 TA 1 - 7.5.9.1
    Adapter driver: <IDE> HA 1

    === Scsi-Device-Map ===
    CdRomPeripheral : NERO IMAGEDRIVE2 1.0h Imagedrv Port 0 ID 0 DMA: Off
    DiskPeripheral : ST380023A atapi Port 1 ID 0 DMA: On
    DiskPeripheral : ST3160021A atapi Port 1 ID 1 DMA: On
    CdRomPeripheral : DVDRW IDE1008 atapi Port 2 ID 0 DMA: Off
    CdRomPeripheral : DVDROM 1 0X atapi Port 2 ID 1 DMA: On
    CdRomPeripheral : AXV CD/DVD-ROM 2.2a a347scsi Port 3 ID 0 DMA: Off
    CdRomPeripheral : Generic DVD-ROM 1.0 d347prt Port 4 ID 0 DMA: Off

    === CDRom-Device-Map ===
    DVDRW IDE1008 E: CDRom0
    DVDROM 1 0X F: CDRom1
    AXV CD/DVD-ROM G: CDRom3
    Generic DVD-ROM H: CDRom4
    NERO IMAGEDRIVE2 I: CDRom2
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 74448896 (0) Byte
    BUFE : 0
    Physical memory : 511MB (523804kB)
    Free physical memory: 109MB (111888kB)
    Memory in use : 78 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    23.2.2007
    UDF/ISO compilation
    21:23:16 #1 Text 0 File SCSIPTICommands.cpp, Line 411
    LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL

    21:23:17 #2 Phase 112 File dlgbrnst.cpp, Line 1746
    DVD-Video files reallocation started

    21:23:17 #3 Phase 114 File dlgbrnst.cpp, Line 1746
    DVD-Video files reallocation completed (no file modified)

    21:23:17 #4 Text 0 File Isodoc.cpp, Line 6509
    UDF document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : FALSE
    Write : TRUE
    Finalize CD : TRUE
    Multisession : FALSE
    Burning mode : DAO
    Mode : 1
    UDF Mode : UDF/ISO bridge
    UDF Options : automatic
    UDF Revision : 1.02
    UDF Partition Type : physical
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet : FALSE
    Allow pathdepth more than 8 directories : TRUE
    Allow more than 255 characters in path : TRUE
    Write ISO9660 ;1 file extensions : TRUE

    21:23:17 #5 Phase 111 File dlgbrnst.cpp, Line 1746
    DVD-Video files sorted

    21:23:18 #6 ISO9660GEN -11 File Geniso.cpp, Line 3332
    First writeable address = 0 (0x00000000)

    21:23:18 #7 ISO9660GEN -11 File Geniso.cpp, Line 3332
    First writeable address = 0 (0x00000000)

    21:23:18 #8 Text 0 File Burncd.cpp, Line 3451
    Turn on Disc-At-Once, using DVD media

    21:23:22 #9 Text 0 File DlgWaitCD.cpp, Line 306
    Last possible write address on media: 2298495 (510:46.45, 4489MB)
    Last address to be written: 836015 (185:46.65, 1632MB)

    21:23:22 #10 Text 0 File DlgWaitCD.cpp, Line 318
    Write in overburning mode: NO (enabled: CD)

    21:23:22 #11 Text 0 File DlgWaitCD.cpp, Line 2903
    Recorder: DVDRW IDE1008, Media type: DVD-R
    Disc Manufacturer: -
    Disc Application Code: 0, Disc Physical Code: 0

    21:23:22 #12 Text 0 File DlgWaitCD.cpp, Line 490
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================

    21:23:22 #13 Text 0 File ThreadedTransferInterface.cpp, Line 821
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 836016 (836016) = #836016/185:46.66
    relocatable, disc pos for caching/writing not required/ required
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 836016 blocks [E: DVDRW IDE1008]
    --------------------------------------------------------------

    21:23:23 #14 Text 0 File ThreadedTransferInterface.cpp, Line 1024
    Prepare [E: DVDRW IDE1008] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1: Idx 0 Idx 1 Next Trk
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 1712160768, ISRC ""
    DAO layout:
    ===========
    ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________
    0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
    0 | 1 | 0 | 0x41 | 836016 | 0 | 0x00
    0 | 1 | 1 | 0x41 | 836016 | 0 | 0x00
    836016 | lead-out | 1 | 0x41 | 0 | 0 | 0x00

    21:23:23 #15 Text 0 File SCSIPTICommands.cpp, Line 209
    SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

    21:23:23 #16 Phase 24 File dlgbrnst.cpp, Line 1746
    Caching of files started

    21:23:23 #17 Text 0 File Burncd.cpp, Line 4278
    Cache writing successful.
     
  2. satter21

    satter21 TS Rookie Topic Starter

    the rest of the error log...

    21:23:23 #18 Phase 25 File dlgbrnst.cpp, Line 1746
    Caching of files completed

    21:23:23 #19 Phase 36 File dlgbrnst.cpp, Line 1746
    Burn process started at 2x (2,770 KB/s)

    21:23:23 #20 Text 0 File ThreadedTransferInterface.cpp, Line 2743
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    21:23:24 #21 Text 0 File DVDR.cpp, Line 3058
    Recording mode: Sequential Recording Mode

    21:23:25 #22 Text 0 File DVDR.cpp, Line 3214
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    21:23:25 #23 SPTI -1066 File SCSIPassThrough.cpp, Line 179
    CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1066)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x24
    Sense Qual: 0x00
    CDB Data: 0xAC 00 00 00 00 00 00 00 00 64 00 00
    Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 24
    Buffer x0671a1c0: Len x648

    21:23:25 #24 Text 0 File Cdrdrv.cpp, Line 9235
    ---- DVD Structure: Physical Format Information (00h) ----
    Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 0 h
    End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
    Data in Burst Cutting Area (BCA) does not exist
    Start sector number of the current Border-Out: 0 h
    Start sector number of the next Border-In: 0 h
    Media Specific [16..63]:
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

    21:23:49 #25 Text 0 File Cdrdrv.cpp, Line 1293
    21:23:49.265 - E: DVDRW IDE1008 : Queue again later

    21:24:58 #26 SPTI -1135 File SCSIPassThrough.cpp, Line 179
    CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135)
    Sense Key: 0x03 (KEY_MEDIUM_ERROR)
    Sense Code: 0x0C
    Sense Qual: 0x00
    CDB Data: 0x2A 00 00 00 02 00 00 00 20 00 00 00
    Sense Area: 0x71 00 03 00 00 00 00 0A 00 00 00 00 0C
    Buffer x07fe0440: Len x10000
    0x00 01 00 00 00 00 00 13 14 01 00 11 00 00 01 01
    0x00 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00
    0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    21:24:58 #27 CDR -1135 File Writer.cpp, Line 299
    Write error
    E: DVDRW IDE1008

    21:24:59 #28 Text 0 File DVDR.cpp, Line 3434
    EndDAO: Last written address was 511

    21:24:59 #29 Phase 38 File dlgbrnst.cpp, Line 1746
    Burn process failed at 2x (2,770 KB/s)

    21:25:00 #30 Text 0 File SCSIPTICommands.cpp, Line 254
    SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

    21:25:02 #31 Text 0 File Cdrdrv.cpp, Line 10472
    DriveLocker: UnLockVolume completed

    21:25:02 #32 Text 0 File SCSIPTICommands.cpp, Line 411
    UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL


    Existing drivers:
    File 'Drivers\PXHELP20.SYS': Ver=2.03.28a, size=20640 bytes, created 01/08/2006 20:48:00 (Prassi/Veritas driver for win 2K)

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
     
  3. eroz

    eroz TS Rookie Posts: 108

    what burn speed did you use? Try using a slower speed....
     
Topic Status:
Not open for further replies.


Add New Comment

TechSpot Members
Login or sign up for free,
it takes about 30 seconds.
You may also...


Get complete access to the TechSpot community. Join thousands of technology enthusiasts that contribute and share knowledge in our forum. Get a private inbox, upload your own photo gallery and more.